- #Kasa smart switch install install
- #Kasa smart switch install manual
- #Kasa smart switch install professional
If there’s more than one switch in the box, make sure they also don’t have electricity flowing to them. The battery-powered tool should beep and light up if it detects current. Waving a non-contact voltage tester inside the junction box is the best way to confirm that electricity is not flowing to the switch. The next step is to remove the cover plate so you can access the switch itself. You’ll find instructions for installing a C by GE C-Start Smart Switch Motion Sensing+Dimmer on a multi-way circuit here, but the upshot is that you’ll need a C by GE smart switch on all the other legs of the circuit. (And if you don’t need all the features this dimmer offers, GE Lighting offers four simpler and less-expensive alternatives.) The first step-and the most important-is to identify which circuit breaker controls the electricity flowing to that switch and to turn it off. In this how-to, we’ll replace a single-pole switch with a C by GE Start Smart Switch Motion Sensing+Dimmer, but the process isn’t radically different for a multi-way circuit. (The latest Wemo WiFi Smart Light Switch 3-Way is an exception to that rule, and it can also be used in a single-pole installation. If you’re replacing a dumb switch on a three- or four-way circuit, you’ll typically need to replace the other switch or switches on that circuit with companion switches from the same company that made the smart swtich you’re installing. If two switches can control it-for example, switches on opposite sides of the room-you have a three-way switch (if more than two switches control the same light, it’s described as a four-way circuit.) If only one switch controls the flow of electricity to that bulb you want to control, you have a single-pole switch. Next, you’ll need to determine if you need a single-pole or a three-way switch. In a three- or four-way circuit, more than one switch can turn the bulb on and off. Single-pole switches are the easiest to replace, since only one switch controls the circuit.
#Kasa smart switch install manual
Get to know more details of each function and configuration please go to Download Center to download the manual of your product.Do you need a single pole switch or three-way? Daniel Masaoka / IDG Step 6 ：Restore power to the Smart Switch at the circuit breaker, and enjoy it. Note: The included wall plate is intended for single gang box installation only. Step 5 ：Mount the Smart Switch onto the wall box using the two screws provided, and snap on the included wall plate or attach your existing one.
Neverconnect the Neutral line to any Switch lines.Note: The following wiring scenarios may be dangerous or illegal. Green wire on switch (Ground line) to Ground line, White wire on switch (Neutral line) to Neutral line. Step 4 ：Connect the Smart Switch wiring with the provided wire connectors as follows.Ĭonnect each of the two black wires from the switch to the available Live linesvia the wire nut, and wrap electrical tape around the wire nuts to make sure the copper conductor Step 3 ：Remove existing faceplate and light switch, then identify Live/Load, Neutral and Groundlines. Use voltage tester to confirm no voltage is present. Step 2: Turn offpower at the circuit breaker that controls the light switch. If you have met the electrical requirements, proceed with the electrical installation instructions below. Due to TP-Link smart switch need to be configured by Wi-Fi, it can only be installed in non-metal faceplates and dry indoor locations. A single pole switch (TP-Link smart switch is not 3-way switch).ģ.
#Kasa smart switch install professional
(If there is no neutral line in the wall box, STOP installing the switch and consult with a professional electrician). Step 1 ：Please confirm whether your electrical line meet the following electrical requirements below:
#Kasa smart switch install install
Note: If you’re not familiar with basic electrical work, please don’t install switch by yourself, and call a professional electrician to help you. Now let’s install the TP-Link smart switch to your electrical line. In general, the electrical line will supply two live lines, one neutral line and one ground line to you to install socket or switch. Ground line: Because the earth is a good conductor, we use a line to connect the shell of device/electrical appliance and the earth to avoid electrical shock hazards, we call the line ground line. Neutral line: Due to the three-phase equilibrium (A, B and C line are connected together at N line), there is no current flows through N line, we call it neutral line. Live/Load line: There will generate voltage (100 ~ 240V) between A/B/C line and N line, we call A, B and C line live/load line. As we know, power transmission usually take the form of three phase four wire. Let’s know about the electrical line at first. How can I install HS200 if my powerline socket only contains 3 lines? Before we start, please note that your socket is applicable:
0 kommentar(er)
